ADM3053BRWZ-REEL7 UART Interface IC CAN Interface IC Sgnl & Pwr Iso Tncvr w/ Intg Iso DC/DC
uart level shifter ic
,usb serial converter chip
ADM3053BRWZ-REEL7 UART Interface IC CAN Interface IC Sgnl & Pwr Iso Tncvr w/ Intg Iso DC/DC
FEATURES
- 2.5 kV rms signal and power isolated CAN transceiver isoPower integrated isolated dc-to-dc converter
- 5 V operation on VCC
- 5 V or 3.3 V operation on VIO
- Complies with ISO 11898 standard
- High speed data rates of up to 1 Mbps
- Unpowered nodes do not disturb the bus
- Connect 110 or more nodes on the bus
- Slope control for reduced EMI
- Thermal shutdown protection
- High common-mode transient immunity: >25 kV/μs Safety and regulatory approvals
- UL recognition
- 2500 V rms for 1 minute per UL 1577
- CSA Component Acceptance Notice 5A
- VDE Certificate of Conformity
- DIN EN 60747-5-2 (VDE 0884 Part 2): 2003-01
- VIORM = 560 V peak
- Industrial operating temperature range (−40°C to +85°C) Available in wide-body, 20-lead SOIC package
APPLICATIONS
- CAN data buses Industrial field networks
GENERAL DESCRIPTION
The ADM3053 is an isolated controller area network (CAN) physical layer transceiver with an integrated isolated dc-to-dc converter. The ADM3053 complies with the ISO 11898 standard.
The device employs Analog Devices, Inc., iCoupler® technology to combine a 2-channel isolator, a CAN transceiver, and Analog Devices isoPower® dc-to-dc converter into a single SOIC surface mount package. An on-chip oscillator outputs a pair of square waveforms that drive an internal transformer to provide isolated power. The device is powered by a single 5 V supply realizing a fully isolated CAN solution.
The ADM3053 creates a fully isolated interface between the CAN protocol controller and the physical layer bus. It is capable of running at data rates of up to 1 Mbps.
The device has current limiting and thermal shutdown features to protect against output short circuits. The part is fully specified over the industrial temperature range and is available in a 20-lead, wide-body SOIC package.
The ADM3053 contains isoPower technology that uses high frequency switching elements to transfer power through the transformer. Special care must be taken during printed circuit board (PCB) layout to meet emissions standards. Refer to the AN-0971 Application Note, Recommendations for Control of Radiated Emissions with isoPower Devices, for details on board layout considerations.
W25N01GVZEIG SLC Nand Flash Memory IC 3V 1G BIT Winbond TW SPI
PF48F4400P0VBQEK NEW AND ORIGINAL STOCK
DSPIC30F3011-30I/PT Flash Memory IC NEW AND ORIGINAL STOCK
IR2110PBF NEW AND ORIGINAL STOCK
S25FL032P0XMFI010 SOP8 104MHz Flash Memory IC Chip
W25Q80DVSNIG Serial Flash Chip 3V 8M BIT Dual Quad Spi Memory Integrated Circuit
MOS Tube Field Effect Single-Chip Drive PWM Controlador Module IRF520
MAX485, RS485 Module TTL To RS-485 Module TTL To 485
SKY65336-11 NEW AND ORIGINAL STOCK
| Image | Part # | Description | |
|---|---|---|---|
|
|
W25N01GVZEIG SLC Nand Flash Memory IC 3V 1G BIT Winbond TW SPI |
FLASH - NAND (SLC) Memory IC 1Gbit SPI - Quad I/O 104 MHz 7 ns 8-WSON (8x6)
|
|
|
|
PF48F4400P0VBQEK NEW AND ORIGINAL STOCK |
FLASH - NOR (MLC) Memory IC 512Mbit CFI 52 MHz 110 ns 64-LBGA (11x13)
|
|
|
|
DSPIC30F3011-30I/PT Flash Memory IC NEW AND ORIGINAL STOCK |
dsPIC dsPIC™ 30F Microcontroller IC 16-Bit 30 MIPs 24KB (8K x 24) FLASH 44-TQFP (10x10)
|
|
|
|
IR2110PBF NEW AND ORIGINAL STOCK |
Half-Bridge Gate Driver IC Non-Inverting 14-DIP
|
|
|
|
S25FL032P0XMFI010 SOP8 104MHz Flash Memory IC Chip |
FLASH - NOR Memory IC 32Mbit SPI - Quad I/O 104 MHz 8-SOIC
|
|
|
|
W25Q80DVSNIG Serial Flash Chip 3V 8M BIT Dual Quad Spi Memory Integrated Circuit |
FLASH - NOR Memory IC 8Mbit SPI - Quad I/O 104 MHz 8-SOIC
|
|
|
|
MOS Tube Field Effect Single-Chip Drive PWM Controlador Module IRF520 |
N-Channel 100 V 9.2A (Tc) 60W (Tc) Through Hole TO-220AB
|
|
|
|
MAX485, RS485 Module TTL To RS-485 Module TTL To 485 |
1/1 Transceiver Half RS422, RS485 8-uMAX/uSOP
|
|
|
|
SKY65336-11 NEW AND ORIGINAL STOCK |
RF Front End 2.4GHz ISM 28-MCM (8x8)
|